What can you put behind a wood burning stove?

Type X drywall is a common material used for wood stove installations. Type X is a gypsum-based drywall that is 5/8 inch thick and is installed on each side of a 2-inch by 4-inch wood stud, spaced 16 inches on center or spaced 24 inches on center.

Type X drywall is a common material used for wood stove installations. Type X is a gypsum-based drywall that is 5/8 inch thick and is installed on each side of a 2-inch by 4-inch wood stud, spaced 16 inches on center or spaced 24 inches on center.

Similarly, can I use cement board behind my wood stove? Safe wood stove installations require a heat shield that will prevent heat from the wood stove from creating a fire hazard in the building materials that form the exterior wall. Hardi cement board is an inexpensive solution that will form the foundation of an effective heat shield for any application.

In this regard, what clearance is required around a wood burning stove?

At least 36 inches of clearance must be allowed between the top of a stove and an unprotected ceiling. Brick or stone provide little or no protection for a combustible wall since they are good conductors of heat.

Can you paint behind a wood burning stove?

Then make sure the surfaces are clean, sound, dry and stable. Protect the stove or fireplace itself using plastic sheets – the last thing you want is splashes of paint on a black wood burning stove! When the area is ready for painting, dilute the first coat of Claypaint with around 1-2 parts water to 8-9 parts paint.

Is Copper a good heat shield?

Polished copper sheet is an excellent heat shield due to the high reflectance, low emissivity, and high rate of heat conduction.

Can you use ceramic tile behind a wood stove?

ANSWER. ANSWER – Ceramic tile behind a woodstove works very well as long as it’s installed correctly over the right type of substrate. It’s important, though, that the tile is attached to a surface that’s not affected by heat. It’s best to use a concrete substrate like a mortar bed or a cementitious backer unit.

Can I tile behind a wood burning stove?

You can absolutely use tiles around the back and sides of your wood burner. However, we recommend using porcelain tiles, which are very heat resistant. We would recommend a heat resistant tile adhesive such as the Palace Heat Resistant Adhesive, onto a good solid surface.

How do you install a heat shield on a wood stove?

Metal Heat Shields Check the certification information on the back of the wood stove for the required distance between the stove and the wall. Locate the studs in the wall behind the wood stove with a stud finder. Hold metal or ceramic spacers against the wall studs, and mark the screw holes with a pencil.

What is the purpose of a flue damper?

A flue damper is a cast iron or steel plate on a spindle fitted inside a flue system (usually in the first length of vitreous enamel flue pipe) which can be rotated by a small handle outside the flue pipe to reduce the adverse affects of a strong flue up-draught or ‘pull’.

Do you need permission to install a wood burning stove?

You do not technically require planning permission to install a wood burning stove, however since 2005 it has been a legal requirement to let your local authority building control department know of your intentions – no matter what type of heating appliance you are installing.

Do I need a hearth for a wood stove?

The hearth should measure at least 840 x 840mm and must have a space of at least 225mm at the front of the stove door. However, if the stove is designed in a way that it burns with doors open, there should be a minimum space of at least 300mm at the front.

Is a damper necessary on a wood stove?

Modern stoves usually do not need a damper. the air flow through the stove.It will also slow down the heat loss out of the flue. If closed down too much it will build creosote in the stack.

How high does a wood stove pipe need to be?

The chimney should extend at least 3 feet above the roof surface it penetrates and 2 feet higher than any roofline or other obstacle within a horizontal distance of 10 feet. Taller chimneys make more draft, but chimneys exposed to outside cold don’t.

How close can a window be to a wood stove?

36 inches

What is considered a non combustible wall?

While wall ‘coverings’ are frequently non-combustible — like tile, brick, stone, metal — the underlying structure often contains wood, paper faced drywall or insulation, and other materials that could catch fire if enough heat were to be transmitted through the ‘non-combustible’ wall covering.

How do you build a brick wall behind a wood stove?

Lay a row of heat-treated bricks over the mortar, confirming that each is level as you lay it with a bubble level. Spread a 1/2-inch thick layer of mortar between each brick using the mortar trowel, to secure them together. Lay additional rows of bricks on the plywood until you have covered the entire piece of plywood.

How do you install a wood burning stove through a wall?

Cutting the Holes Position the stove so the back is at least 16 inches from an outside wall. Attach the 90-degree elbow temporarily onto one end of the long section of chimney pipe. Locate and mark a stud in the wall at each side of the mark, using a stud finder. Cut the outline in wood paneling, using a jigsaw.